KNG Firmware Releases *************************************************************** Release KNG-Pxxx Portables Ver. 5.0.0 KNG_Portable_5.0.0.exe KNG-Mxxx Mobiles Ver. 5.0.0 KNG_Mobile_5.0.0.exe KAA0660 Remote Control Head Ver. 5.0.0 KNG_RCH_5.0.0.exe KAA0670 Handheld Control Head Ver. 5.0.0 KNG_HCH_5.0.0.exe Minimum Neovision Editor KAA0732 Ver. 2.0.0 Neovision ASK Editor KAA0735 Ver. 2.0.0 Features TDMA Support TDMA: group regroup & dynamic regroup P25 Trunking: OTAP read enhancement P25 Trunking: Static SNDCP Data Registration P25 Trunking: Forced System Reset P25 Trunking: Enhanced Roaming P25 Trunking: Roaming Notifications P25 Trunking: Failsoft by Personality Conventional: Add "radio name" display choice to programming/cloning Add ability to display radio name/alias instead of UID Make low battery warnings selectable backlight toggle incompatibility Make RCE crypto work with TDMA Add trunked DTMF all-call alert to sentinel operation Return to last active RX channel when exiting scan Single button channel scan + priority scan Make secure LED operation the same for trunking as it is for conventional After Keypad select of 'Backlight off', backlight continues to operate for key presses Automatically translate trunked call alerts for multiple unit IDs to DTMF alerts Add AlgID + KeyID for RX of key not in alias table Keypad programming should allow deletion of command zones Picklist cloning should include Two-Tone, MDC and DTMF lists Add call alert UI support on the HHCH Change MDC encode features to allow hex input Add MDC inhibit & uninhibit encode operation Add HHCH speaker parameters to keypad programming Conventional P25 call alert support for group addresses MDC call alert & voice selective call encode Display useful message if Warm-Start store key fails Bug Fixs Incorrect priority scan indicator P25 Trunking: Lockup if improperly programmed P25 Trunking: busy UI state not updating properly P25 Trunking: Group Regrouping Denies in Australia P25 Trunking: Site Search soft key assignments incorrect P25 Trunking: dual mode scan nuisance delete bugs P25 Trunking: site affilliation display incorrect P25 Trunking: False PTT OTAR: KMM responses aren't sent while scanning Dual Mode Scan: Lockup when turning scan off/on while receiving/transmitting Dual Mode Scan: Speed up conventional scanning Dual Mode Scan: Errors when removing all trunking channels from list Conventional: Scan lockup Conventional: scanning quits Conventional: channel busy fails when set to status symbol Conventional: RX is interrupted by unit call selection Conventional: priority conv scan lockup Conventional: TX 2-tone w/ tone B = 0 causes TX lockup Conventional: 2-tone TX menu item cut-off on portable Conventional: priority scan failure Conventional: PRI 1 takes too long to override PRI 2 Conventional: secure strapped revert emergency call keyfail lockup Conventional: scan deactivation causes icons to stick Conventional: busy channel lockout fails for digital Conventional: encryption LED fails during scan Conventional: NAC picklist shows empty entries Conventional: simultaneous cloning causes lockups Conventional: cloning failure causes lockup Conventional: keypad programming prohibits TGID=0 Conventional: zone scan fails on non-sequential zones Conventional: RX mode icon wrong if RX dequalifies System calls causing mobile sluggishness Flashing the radio with all 5 images causes splash screen to stick Mobile menu can get stuck Busy channel lockout (carrier) failure with active channel SLN=0 causes various problems GPS coordinates not displayed properly TX secure behaves erratically P800 always aligns RSSI scale to the same number Sentinel DTMF ID of 0000 results in indefinite tx Manual two-tone signaling causes transmit stick on the mobile Conventional data messages do not check receive mode Offhook scan enable should be made independent of the offhook monitor option Disply of my own UID is not always correct Radio goes into Monitor Mode inadvertently If System Priority and Zone Priority point to the same channel, Priority doesn't work MDC signal causes transmit stick Failed P25 call alert "OK" button leaves you in a menu you cannot escape from Digital RX causes unqualified UI indications after end of message Voice mute icon does not always display for automatic voice mute Backlight during scan comes on more often than it should Enabling conventional scan and dual mode scan at same time Priority scan fails if Pri1 is system-based Encryption will do a "Key Fail" with tone on first PTT only KNG Firmware Releases *************************************************************** Release Portable/ Mobile 4.6.2 Control Head/ HCH 4.6.2 Minimum Neovision Editor Rev. 1.5.0 Features P25 Trunking - Dynamic Regroup Display MDC ID's as decimal as an option Support MDC group, fleet & wildcard addressing Support long block MDC Enable ID alias lookup for MDC signaling Stop premature low battery during TX with IS pack No keypad editing lockout for call list picklist Rapid scroll feature needs to be added to trunking Add Clear Tx Beep to Mixed Mode Analog Tx Add mobile accessory output option for transmit indication Automatic voice mute per-channel Add alternate display line options Talkaround optionally applies on a per-channel basis Allow command zone channel add feature to work with trunking channels Add a way to monitor GPS statistics through the USB DMS: Speed up OOR scanning; implement OOR icon Add support for Motorola wide pulse modulation Make voice mute operation per-channel instead of per-zone Add ability to rapidly scroll through long menu Remember last channel of each zone during zone change Improve AMBE noise cancellation Add use group key for unit call and make it default to true Beep when Priority goes active Portable: Soft Power Down Portable: Toggle Switch Zone Select Bug Fixes Correct MDC voice mute operation to account for long block packets Green LED operation is not consistent in Voice Mute MDC ANI can cause ID = 0 display if MDC voice mute is enabled for the ANI ID MDC Unit ID reappears after Monitor Mode is changed from open ID display during scan hold does not work if MDC is sent at end of TX P25 Trnk - Priority on Selected not initialized after download P25 Trnk - Unit Call denied by FNE P25 Trk - Unit Call Accept button doesn't work P25 Trk - Radio displays "Emergency" when transmitting P25 Trk - Dual Mode Scan lockup P25 Trk: Cassidian systems cause radio to group affiliate to 0 P25 Trk: TG busy indication doesn't work on older Harris systems OTAR: Deleting last TEK in radio causes response KMM to fail OTAR: Radio doesn't always deregister during scan Incorrect KEK can cause OTAR Registration to fail when it shouldn't Off-hook settings for Scan depends on Off-hook setting for Monitor Priority scan on digital channel can cause infinite scan hold time Powerup zone should be last zone not toggle switch zone A radio with Talkback Scan enabled can transmit a TGID of 65535 RXA with code guard causes RXA Icon to stick until channel changed or power cycle A new channel added through keypad programming doesn't show up until a zone cycle Keypad programming display lines can be navigated even when locked out Mobile backlight only goes from off to on if the soft keys are pressed Keypad programming unit call alias cuts off on the mobile and control head display Toggling channel scan disables secure transmit Key fail display prevents rapid channel changes Zone scan cannot be changed while scanning Smart-mic backlight will not turn-on P25 Trk: Harris County/City of Houston zone overlap issue DMS: Out of range radio won't scan to conventional channels DMS List Edit - View option doesn't display some channels Toggle switches can be ignored during unit call RX ------------------------------------------------------------------ Release Portable/ Mobile 4.5.0 Control Head 4.5.0 Minimum Neovision Editor Rev. 1.4.19 Add Support for Mobile GPS option Add Home channel button assignment Add Channel Number + Zone Label display line selection Add Dual Mode Scan List user selection Add DTMF decode on digital channels (Voice Mute) Add Mobile I/O support for COR on trunked systems Add Mobile display dimmer Add Trunking wide area single site support Add Allow Vote scan list selection Enhance Additional keypad programming functions Enhance Show/Hide own Unit ID when Unit ID is programmed as display item Enhance Allow squelch adjustment per channel Enhance Legacy cloning operation Enhance Expanded two-tone notification timing Enhance Trunked preferred site operation Enhance OTAR: Multiple group RSI support Fix Changed preset squelch value to allow audio at lower signal level Fix Allow Tx/Rx while in menu operation ------------------------------------------------------------------ Release Portable/ Mobile 4.4.0 Control Head 4.4.0 Minimum Neovision Editor Rev. 1.4.17 Add MDC Support Add Command Zone Operation Add Messaging Capabilities Text Messaging User Status Messaging Add Paging and Call Alert Two-Tone Paging DTMF Paging MDC1200 Paging Call Alert Paging Radio Check Add Radio Inhibit/Uninhibit Add Enhanced Lockout Feature Set Add Auxiliary Input/Output Functions for mobile ------------------------------------------------------------------ Release Portable/ Mobile 4.02.16 Control Head 4.02.11 Minimum Neovision Editor Rev. 1.4.15 Add Display ‘Call Alert Successful message Add P25 Trunk Unit Call messages Add Conventional scan preamble for TSBK ISPs and Data Add RCII Diagnostic Send ISP capabilities Add Allow RX audio while in sub-menus Fix Conventional emergency channel selection Fix Talkback encryption key Fix Disable battery monitor during transmit Fix OTAR MAC calculation interference with conventional channel encryption operation ------------------------------------------------------------------ Release Portable/ Mobile 4.02.15 Control Head 4.02.11 Required Neovision Editor 1.4.12 Fix Site trunking to wide area trunking transition ------------------------------------------------------------------ Release Portable/ Mobile 4.02.13 Control Head 4.02.11 Required Neovision Editor 1.4.12 Add Conventional OTAR capabilities Fix Trunking OTAR: Reestablish key conditions once radio is rekeyed Fix Minnesota Trunking: Inhibit after an emergency fix ------------------------------------------------------------------ Release 4.02.12 Required Neovision Editor 1.4.8 Add Add wait/add identifiers if not present during control channel validation Enhance Status Update Enhancements Fix Radio displays DSP Error 1 after NeoVision download/power cycle. Fix Trunking Scan Lockup Fix Harris P25 Trunking: OTAR Registration ------------------------------------------------------------------ Release 4.02.08 Required Neovision Editor 1.4.7 Add Keyset Select assigned in menu and button Add DSP: Add eeprom protection Add Mobile: Add backlight level menu settings Add P25 Trunking Emergency Call Cancel Add Trunking Unit Call without availability check (Harris) Add Trunking OTAR Option ability Add Mobile: Add fixed MENU softkey on right side of display Enhance Mobile soft button indication that feature is on Fix Autoscan UI issue Fix Trunking Emergency Alarm use emergency group instead of current working group Fix Trunking early receive LED not turning off in all cases Fix P25 trunking group call audio opens slow Fix P25 Trunking: Source ID of zero slows audio open speeds of unit call and group re-grouping calls Fix P25 Trunking: Group call unit ID of 0 displayed Fix Unwanted transmission after power-on with PTT held. Fix P25 Trunking: earlier LED illumination for group calls Fix P800 and M800 improve RX hum and noise.